|
C2-2350A Universal I/O Video Switcher/Scaler
is based on TV One’s exclusive CORIO®2 technology and provides high
quality bi-directional conversion between a variety of video formats.
Inputs and Outputs can be DVI, RGB, YUV, YPbPr, Composite or S-Video
(YC). Incoming video parameters may be adjusted. All settings are
stored in non-volatile memory and are retained even when power is
switched off. Ten user defined presets are also available to customize
settings for various applications. The high resolution RGB/YPbPr output
is selectable as virtually any PC or HDTV resolution. Our exclusive
AutoSet feature takes the hassle out of setup by automatically sizing
and positioning the computer input image to fit exactly on the video
screen. NTSC, PAL, PAL-M, PAL-N, SECAM standards are supported. The C2-2355A provides an SD/HD-SDI Input and Output in addition to all of the features of the C2-2350A.
All
the functions can be controlled via the front panel Push Buttons,
Infrared, RS-232 or IP. Windows Control Panel software is provided and
most third party control systems interface directly with the entire C2
range of products. A front panel LCD makes setup easy. The unit is
housed in a desktop case and an optional rackmount kit is available
that holds one or two units.
Variable Zoom to
10X enlarges any part of the computer screen to fill the entire video
screen and position controls allow movement to any area desired.
Variable Shrink to as little as 10% allows fitting the image onto most
displays. The advanced Digital Flicker Elimination circuitry and high
sampling rate insures crisp, clear images, while full bandwidth chroma
sampling insures faithfully reproduced, high resolution colors. Motion
compensation, diagonal interpolation and a 3:2 Pulldown feature for
NTSC improves the image quality. Temporal interpolation greatly
improves frame-rate conversion by analyzing and merging successive
frames. Pixel Level Motion Adaptive Diagonal Interpolation insures high
quality de-interlacing of PAL and NTSC signals.
Advanced Features - The Key Mode
allows computer graphics to be keyed over an external Composite, YC or
SDI signal. The keyed image may be faded in and out. Due to the 4:4:4
sampling format, precise keying at the pixel level can be achieved. The
Mix Mode permits Seamless Cut, Fade or Wipe transitions between input sources. The PIP Mode
allows either of the computer inputs to be inset in a window over
either of the video inputs or vice versa. The PIP window may be placed
anywhere on the screen. The Edge Blending
feature allows feathering any or all of the edges; multiple images can
be aligned vertically, horizontally, or both to create unusual
displays. Using multiple units, any number of images can be blended.
Gamma correction is employed to compensate for many of the problems
faced when blending projectors. The Genlock
feature insures precise synchronization of the incoming signals by
providing a wide Subcarrier lock range with Subcarrier phase adjust.
Input Expansion
is possible by using the optional S2 Series Input Expansion Switchers
for SD/HD-SDI, DVI, RGB, YPbPr, YUV, Composite or YC. These units link
to C2 unit via an OPTIONS Interconnect Cable and become an integral
part of the main unit from a control and operational standpoint. The
routing of these additional inputs is controlled directly from the
control system of the C2 unit. Multiple different S2 models may be
simultaneously connected to a single C2 unit.
Basic Stereo Audio
switching is accomplished by an integral 4x1 audio routing switcher.
The four impedance-independent, unbalanced inputs follow the video
input selection. A rear panel terminal block provides input and output
access.
Advanced Stereo Audio
is available via the optional S2-106AD Input Expansion Switcher,
providing six differential audio inputs, which can be used for low
impedance balanced or high impedance unbalanced sources. The user
controls audio level, audio sampling frequencies and up to 999ms of
adjustable audio delay independently for each input. The unit has
numerous choices for audio I/O connectors, including a terminal block.
The S2-106AD connects to the C2 unit via the OPTIONS interconnect cable
and is then fully integrated into the control system of the host unit.
|
